The No.1 Website for Pro Audio

Model 2A

Teac Model 2A
0 Own It
0 Used It
0 Want It
0 Watch It


6 input / 4 output mixer designed

for true multi-channel recording.

Each channel has seperate input selectors, tone control,

channel assign selectors with pan, and input faders.

There is also a MASTER output fader control.

Input selector switch for mic/line or mic att,
which activates a 20dB attenuator pad located,

before the mic preamp stage.

Channel assignments buttons color coded
for the 4 different output busses.

Any signal from a input channel can be assigned

to any, or all of the output channels.

When more than one channel is assigned,

Pan control is engaged = the ability to move the sound

from extreme left or right

in the sound spectrum or anywhere between.

Variable treble control +/-12dB.

Variable bass control +/-12dB.

Crosstalk: Greater then 50dB.

Overall distortion(input to output)=
0.1% THD maximum at nominal -10dB output.

Fader attenuation: Greater then 60dB.

Mic impedance:150~10K.

Input impedance:50K or higher.

Input level: -10dB (0.3V)

Line output/Aux.Output:
Load impedance:10K or higher unbalanced.

Output level: -10dB (0.3volt)

Signal to noise ratio:
One input= greater than 62dB,WTD.

6 inputs = greater than 55dB,WTD.

Frequency response: 30Hz~20KHz,+/-2dB.

Cue output:
Load impedance: Greater than 50K.

Level: -20dB (0.1V) with nominal input.

Buss input:
Input impedance: 15K.

Nominal level: -10dB(0.3V)

Accessory Send/Receive:
Send load impedance:Greater than 10K.

Nominal send level: -10dB(0.3V)

Receive impedance: 15K.

Nominal receive level: -10dB(0.3V)

MIC IN = 1/4 Phone plug.

LINE IN = RCA. Normally you would patch the output
of your reel to reel here (line 1-4)

and the master recorder to (line 5-6),

but you have more options because the meterbridge.

ACCESSORY Send/Receive = a patch point for

additional signal processing like different external

EQ unit, Echo,Reverb, Noise reduction etc.

Access with jumpers included.

AUX OUT = Additional line output in paralell
with the main line output.

LINE OUT = (4)Program buss out.

CUE OUT = A foldback after the the mic preamp stage
unaffected by the input fader.

Power Requirements: 117V A.C, 60hz, 5W
Weight: 13.2 lbs (mixer with no meterbridge attached)

13-1/2 deep. 13-3/8 Wide. 4 Tall.

Made 1976.


Nasty, crunchy, dirty 70's mixers?

...to make a go at the recording biz on a budget. Biamp fits the bill, as does Yamaha PM430, Teac Model 2A / 3, Carvin, Sound Workshop and early Peavey. I remember lusting after an old Lamb 4-buss to go with a Dokorder 7140. Sky

View Post

Pictures Of Mic'ed Up Drum Kits In The Studio

...- Audix D2 - Avalon M2 - SSL 611 OHS - Neumann KM84’s - Brent Averill Neve 1272 Hihats - Mesanovic Model 2A - Neve 33115 Room Mono - Josephson C705 - Langevin AM16

View Post

Teac Model 2a mixer

...4 tape outs (which are rca) going into my mixer line in's (also rca) on the Teac model 2a.....as soon as i make the connection it shoots up the meters on the 4 track and goes a little bonkers.... however, after some experimenting, i notice that it will work...

View Post


Nobody has reviewed this product yet. Have an opinion?

Video Guides