The No.1 Website for Pro Audio
Mytek users!
Old 31st October 2002
  #1
Lives for gear
 
cashewcupcake's Avatar
 
🎧 15 years
Mytek users!

Hi I just got one of the mytek converters in the white face version.

I've been trying to set the levels for each channel using the little recessed screws. It seems that to calibrate the channels to identical level, each channel requires a different screw setting.

Is this the situation for you?

Thanks!

Old 31st October 2002
  #2
One with big hooves
 
Jay Kahrs's Avatar
 
🎧 15 years
I set the gains on my older Mytek to -14dBfs = 0VU when I bought it. I'm not sure if each trim pot is at the same point in it's rotation or not, nor do I really care. It's the kind of thing that you don't usually need to adjust once you set it.
Old 31st October 2002
  #3
Lives for gear
 
groundcontrol's Avatar
 
🎧 15 years
I don't know the Mytek's but in most quality gear, the trimpots used for calibration are multiturn types and their value at any given point of physical rotation is not necessarily related between different ones. For that they would have to closely match them which would serve no purpose since you normally set them in some sort of calibration mode and forget them unlike pots on the front of a multi-channel piece of equipment where you are trying to match settings all the time. Even the best stuff doesn't have really tightly matched pots, hence the need for expensive switched-position controls on mastering-grade equipment.

Just my $0.02!
Old 31st October 2002
  #4
Lives for gear
 
cashewcupcake's Avatar
 
🎧 15 years
I asked because I was wondering if it was f'd up. I bought it used.

Anyone know of a website where I can download some test tones and test levels to help calibrate with?
Old 31st October 2002
  #5
Founder
 
Jules's Avatar
A test CD is always a good thing to have around...

Has 440

SMPTE

Tone sweeps

Levels

White / pink noise

Etc
Old 31st October 2002
  #6
Gear Guru
 
NathanEldred's Avatar
 
7 Reviews written
🎧 15 years
If you're tracking with it and using it to mix to 'two bus' digital you will most definitely need to reset the trim between the two.
Old 31st October 2002
  #7
Gear Head
 
nick's Avatar
 
🎧 15 years
Quote:
Originally posted by faeflora
Anyone know of a website where I can download some test tones and test levels to help calibrate with?
If you've got a mac you can use this:

Make a Test Tone

Hope that helps.
Old 31st October 2002
  #8
Gear Addict
 
CrazyBeast's Avatar
 
🎧 15 years
Quote:
Originally posted by nick


If you've got a mac you can use this:

Make a Test Tone

Hope that helps.
I'll have to check that out. I've always used the Signal Generator plugin in Pro Tools. Pretty simple but works for some things.
Old 31st October 2002
  #9
Jax
Lives for gear
 
🎧 15 years
Quote:
Originally posted by NathanEldred
If you're tracking with it and using it to mix to 'two bus' digital you will most definitely need to reset the trim between the two.
I don't follow your thought process here. Why would you need to reset the trim pots between tracking and mixing? What changes?

I notice my Mytek 8X96's need weekly recalibrating because the pots slip a little more than I would like. I recalib. the D/A, when the voltage at the output gets lower than 1.220 (1.225V = 0dBFS referenced to 1khz at -15dB).
Old 31st October 2002
  #10
Gear Guru
 
NathanEldred's Avatar
 
7 Reviews written
🎧 15 years
Quote:
I don't follow your thought process here. Why would you need to reset the trim pots between tracking and mixing? What changes?
It's a headroom issue. It's not so simple an issue as turning down the ouput of the mic preamp (or compressor) or the console output. They need to stay at optimum levels. Generally I find that I have to set an A/D to -18 or -20 when tracking (especially with really transient material like percussion). Compression helps a little, but I don't like to over do it....I don't generally use fast attack times anyway. For an entire mix I can set the ADC anywhere from -16 to -12 (about +4 to +8 in real world) depending on the type of music and the amount of compression on the two bus. A whole mix is generally more controlled, and after running the mix to tape I want to transfer to digital as hot as possible. Sorry, that's as technical as I get, it's all instinct and ears from there...
Old 2nd November 2002
  #11
Jax
Lives for gear
 
🎧 15 years
Nathan, that's an interesting approach, and one I've not heard of before. Allowing more headroom for tracking certainly makes sense. At mix time, I often rely on compression to knock down peaks more than I would like to. If I had more room to work with because the tracks had a higher ceiling, I could generally preserve more dynamic range.

If I don't get sick of rolling out the converter rack for calibration each time I want to record or mix, this might handle that issue fairly well. I'll try it.

Old 3rd November 2002
  #12
Gear Guru
 
NathanEldred's Avatar
 
7 Reviews written
🎧 15 years
Quote:
Originally posted by Jax
At mix time, I often rely on compression to knock down peaks more than I would like to. If I had more room to work with because the tracks had a higher ceiling, I could generally preserve more dynamic range.
Yep, that's what it's all about. Good Luck Jax.
πŸ“ Reply

Similar Threads

Thread / Thread Starter Replies / Views Last Post
replies: 55 views: 29738
Avatar for IM WHO YOU THINK
IM WHO YOU THINK 13th October 2020
replies: 1296 views: 176775
Avatar for heraldo_jones
heraldo_jones 1st February 2016
Post Reply

Welcome to the Gearspace Pro Audio Community!

Registration benefits include:
  • The ability to reply to and create new discussions
  • Access to members-only giveaways & competitions
  • Interact with VIP industry experts in our guest Q&As
  • Access to members-only sub forum discussions
  • Access to members-only Chat Room
  • Get INSTANT ACCESS to the world's best private pro audio Classifieds for only USD $20/year
  • Promote your eBay auctions and Reverb.com listings for free
  • Remove this message!
You need an account to post a reply. Create a username and password below and an account will be created and your post entered.


 
 
Slide to join now Processing…

Forum Jump
Forum Jump